Just How to Remove as Well as Replace a Bath Tub
Just How to Remove as Well as Replace a Bath Tub
Blog Article
Here in the next paragraph yow will discover a good deal of very good help and advice around How to Install a Bathtub Yourself.
Mounting a tub isn't specifically rocket science, yet it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a new one is likewise a reasonably tough task. If the old tub is conveniently available, the task can move immediately; if you have to open a wall surface to eliminate the old bathtub and place the brand-new tub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have qualified on your own for the job as well as fit attempting it. Instead of working with a contractor to take control of a halfway-completed task, it is better to think about using one before you begin. Possibilities are you might need an expert plumber to make tube links.
This article will help you set up a brand-new bathtub in your restroom if you have actually currently acquired a new bathtub and also don't need to alter the plan of your previous water pipes.
Your tools as well as product list need to comprise the following:
Getting ready for the Installment
To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather bothersome because of the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bathtub
Making use of the two wood boards under its feet, place the tub in the required setting. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub up until the level reads degree.
To mount taps, fit all-time low of the outermost flexible faucet connector to the suitable supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill the tub as well as also inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least when as this will settle it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture an inflexible seal, creating the water to permeate the wall between the bathroom and also the tiling, causing issues with dampness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealer can break fairly very early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that post on How to Install a Bathtub Yourself when doing a lookup on the internet. Sharing is nice. One never knows, you may just be helping someone out. Thanks a bunch for your time. Come back soon.
Estimate
Report this page